Product ratings

4.4

Rate product

Filter reviews by number of stars.

You can only filter by number of stars if there are matching reviews.

5 stars

4 stars

3 stars

2 stars

1 star

Pros

Cons

44 reviews

romane.donnet
4 years ago • purchased this product
purchased this product
Really great!
I bought it as my first 3d printer and I was able to install and use it in less than an hour very easily. I ran my first print directly (the little boat) and was blown away by the quality. Since 3 months of use (even with 5-6 hours of printing) no problem. Whether it is with the provided FlashPrint software or with Cura and Avdenturer client to send GCODE by wifi I never had any problem.
Pro
Easy installation
Software provided FlashPrint
Tree printing support
Quality
Compatibility with CURA
Price
Contra
Proprietary wire
Wire tray too small for large rolls
Printing plate difficult to clean
Built-in webcam useless
15x15x15 a bit small for big projects
The thread vacuum cleaner jumps around from time to time
UN3X
5 years ago
Price performance top. Recommendable for the entry. For 3D printing professionals rather nothing.
Price performance is very good!
As long as you print with Flashprint (the in-house slicer soft of Flashforge), as well as the original Flashforge filament, the print result was extremely good!
This changes when using third party filaments. Especially those with special additives (e.g. fluorescent filament... very sticky and abrasive!). Also the white Purefil-filament worked very bad on this printer.
Remedy should bring a new version of the Nozzle, which was unfortunately not yet equipped. (Retrofitting with about 35.- relatively cheap over various online shops possible) Exchange of Nozzle is commendably easy with this device.
If you have problems with third party filaments, try the following:
- Before each new print, "pierce" the nozzle and remove any print residue.
Do not print too hot (205 was always enough) and with a maximum of 40mm/s. If you print too hot and/or too fast, this will lead to sticking/clogging of the nozzle and ugly transfer motor knocking after a few minutes with the old nozzle and foreign filament.
Pro
Price/Performance
Print quality with original Flashforge-filament very good
Easy maintenance and nozzle change
Quiet printing
Integrated camera (picture quality rather weak though)
Looks nice :)
Print via WLAN, LAN,USB or cloud services possible
Easy to use
Flashprint slicer software very beginner friendly
Contra
Not yet the latest Nozzle installed
Therefore problems with third party filament
Special GCode, which makes it difficult to use third-party slicer software (e.g. Slic3r)
WLAN: Keeps changing the IP in the network after switching off and on despite being fixed in the router
Icebaer1
5 years ago • purchased this product
purchased this product
Would buy it again immediately!
Am thrilled!
Just a great machine with very good workmanship.
Super easy to use and prints great parts!
Pro
- Very good workmanship.
- Very quiet.
- Camera, cloud functions, slice software, ... just top
- Great printing results!
- For such a device, very good price.
Contra
no swiss power cable
Filament tray only for small rolls.
Alpenmutz
4 years ago • purchased this product
purchased this product
Absolute recommendation
Find the price OK
with 15 x 15 x 15 cm certainly not the largest, but as a beginner model to gain some experience, for me super!

Data via USB I could not transfer until now, ie I could not put something on the stick on the PC and print on the 3-D printer, USB stick not supported appears. But via LAN or WIFI, of course, this is also wonderful.
Pro
delivered assembled
switch on and start immediately
quiet (can continue working next door)
my wife is also fascinated :-)
Prints independently (PC does not have to run)
Contra
the included filament is a bit little
no swiss power cable included
opus11_11
4 years ago • purchased this product
purchased this product
Great model for beginners
I was able to put this device into operation without any problems. Already the first print worked great. The printer processes PLA and ABS. The printed parts are true to size and stable.
I don't have the opportunity to compare it to printers in the 3,000 CHF class; but in this price range, the printer can be recommended at any time.
As 3D modeling software I use Fusion 360, which is free for home users.
Pro
Works right away
Very good printing results
Contra
Diameter of the filament rolls limited
stojkajs
4 years ago • purchased this product
purchased this product
Pertect!!!
Pro
Good part
Camera can also be operated without Cloud!
Very professional for a beginner
Would buy it again
Contra
Little louder than described :D